DEFAULT

Sansurfer port 2 loop

Installing SANsurfer diagnostic software. The SANsurfer program analyzes the configuration of the fibre-channel HBA and runs tests on it, such as the Loopback Data Test and the Read/Write Buffer Test. The program is contained on the IBM QLogic 8 Gb FC Single-Port or Dual-Port HBAs for IBM System x® Support CD, which comes with the SSPC server. 2 Port / Nameserver / Fabric Information- QLogic Corporation logging into the switch port, if it is trying to transition from a Loop device (FL_Port) to a Fabric Point-to-Point device (F_Port). This can also be due to compatibility issues with the device's firmware and/or OS driver software. the SANsurfer Switch Manager, or commands as. Our virtual SAN failed over last night (FalconStor IPStor) and two of our three newly deployed blade servers crashed with a BSOD. In troubleshooting the problem I noticed that on the two problem servers, each show a "loop" down on one of the QLogic mezzanine ports in the SANSurfer .

Sansurfer port 2 loop

My environment is as follows: Two IBM X (clustered) Each Sansurfer see s both HBA s on each server but one on each server Both ports on the McData that the Loop Down HBA s are on show port status as Inactive. Loop vs. fabric Vendors submitted four switches, two of each model, for testing. 16 HA (16 port) Firmware SANsurfer management Commonality. the HBA ports. To determine the state of the HBA ports, you can view the light- emitting diodes (LEDs) on the HBA and run a loopback data test by using the SANsurfer program. Off, Off, On/Flashing, Online, 2 Gbps link / I/O activity. Off, On/. At that same time, 2 of 3 blades BSODed and now only see disk down one of the 2 HBA ports. He also said NPIV is enabled on all ports. ii. SN H. SANsurfer FC HBA Manager User's Guide the ports ( transmit and receive transceivers) on the adapter and the error rate. ❑. Perform . local loop, Fibre Channel hub, Fibre Channel switch, or any combination of those. Page ii. SN F. S. SANsurfer FC HBA CLI User's Guide. Command Line Added Appendix B: XML Format 2. Appendix B . Removed run loopback test (command line option. -kl). Added XML format for HBA port alias ( command. My environment is as follows: Two IBM X (clustered) Each Sansurfer see s both HBA s on each server but one on each server Both ports on the McData that the Loop Down HBA s are on show port status as Inactive. Loop vs. fabric Vendors submitted four switches, two of each model, for testing. 16 HA (16 port) Firmware SANsurfer management Commonality. the HBA ports. To determine the state of the HBA ports, you can view the light- emitting diodes (LEDs) on the HBA and run a loopback data test by using the SANsurfer program. Off, Off, On/Flashing, Online, 2 Gbps link / I/O activity. Off, On/. Figure 2. HBA Information Menu SANsurfer FC/CNA HBA CLI v Build 32 HBA 2: Port 2: WWPN: BB-DE Online HBA Model QLE 3: Firmware Version: Actual Connection Mode: Loop Actual Data Rate . Installing SANsurfer diagnostic software. The SANsurfer program analyzes the configuration of the fibre-channel HBA and runs tests on it, such as the Loopback Data Test and the Read/Write Buffer Test. The program is contained on the IBM QLogic 8 Gb FC Single-Port or Dual-Port HBAs for IBM System x® Support CD, which comes with the SSPC server. Jan 08,  · Do one of the following to start SANsurfer FC HBA CLI in interactive mode: scli INT or scli NOTE: When starting SANsurfer FC HBA CLI on a Solaris console serial port connection, the application may be slow to launch. To resolve this issue, specify the INT flag, as shown above. Here is a sample: sunsrv01# scli SANsurfer FC HBA CLI v Build. Our virtual SAN failed over last night (FalconStor IPStor) and two of our three newly deployed blade servers crashed with a BSOD. In troubleshooting the problem I noticed that on the two problem servers, each show a "loop" down on one of the QLogic mezzanine ports in the SANSurfer . 2 Port / Nameserver / Fabric Information- QLogic Corporation logging into the switch port, if it is trying to transition from a Loop device (FL_Port) to a Fabric Point-to-Point device (F_Port). This can also be due to compatibility issues with the device's firmware and/or OS driver software. the SANsurfer Switch Manager, or commands as. 1. Overview. This readme file is intended for use with QLogic's SANsurfer FC HBA CLI for Windows Server Storport Miniport (x86 and x64) in conjuntion with QLogic's N_Port ID Virtualization (NPIV)-capable Windows driver. Prior to QLogic Fibre Channel SanBox2 Switch Firmware Version - , moving a target from one port to another port of a switch results in the target device not being reported to the driver during Name Server query for the list of devices.

Watch Now Sansurfer Port 2 Loop

Introduction to StorFusion™ Demo 2 – Fabric Assigned Port Worldwide Name (FA-WWN), time: 10:50
Tags: Holy soldier last train 1992 adobe , , Router wifi windows 8 , , Kathalipathu epad ink software . Our virtual SAN failed over last night (FalconStor IPStor) and two of our three newly deployed blade servers crashed with a BSOD. In troubleshooting the problem I noticed that on the two problem servers, each show a "loop" down on one of the QLogic mezzanine ports in the SANSurfer . Prior to QLogic Fibre Channel SanBox2 Switch Firmware Version - , moving a target from one port to another port of a switch results in the target device not being reported to the driver during Name Server query for the list of devices. 1. Overview. This readme file is intended for use with QLogic's SANsurfer FC HBA CLI for Windows Server Storport Miniport (x86 and x64) in conjuntion with QLogic's N_Port ID Virtualization (NPIV)-capable Windows driver.

5 thoughts on “Sansurfer port 2 loop

  1. You have hit the mark. It seems to me it is very good thought. Completely with you I will agree.

  2. Unfortunately, I can help nothing. I think, you will find the correct decision. Do not despair.

Leave a Reply

Your email address will not be published. Required fields are marked *